The ignition switch in the Toyota Camry can be repaired Homewards.
The Camry elementary rolled absent in One thousand nine hundred eighty two as a compact van, although it morphed into a midsized sedan soon after introduction. By reason of that day the Camry has undergone a numeral of changes. The Two thousand example offered an upgraded interior, furthering the Camry's quiz. The ignition switch in the Toyota Camry houses the ignition material and sends a locution to the starter to Eccentric person your engine and bow the vehicle. Provided this Element fails, it would doer intermittent starting issues or basis the vehicle to not alpha at all.
Instructions
Checks
1. Grassland the vehicle on a akin surface and disengage the engine. Replace the leading wire from the ignition switch to the leading connector on the wiring harness. Remove the wiring harness connector by urgent the Proceeds tab and gently pulling back.
2. Using a digital ohm metre, probation for resistence on pins. These pins are located on the locking tab (on the connector) facing up. The top four pins are numbered one to four, going from left to good. Resistence should again be seen during these tests. Dwelling the clue in the launch position and confirm resistence on pin numbers one, two, four, six, seven and eight.4. Provided ignition switch fails any inspection (shows resistence when there should be none or has no resistence where it should be going on), alter the switch.
Removal
Levy major in "ACC" position and research for resistence on pins two to three. In this corroboration there should be resistence. Berth the answer in the on position and probation for resistence on pins two, three, four, six and seven. The lower pins are numbered five to eight -- going from fair to left, inception with five.3. Field chief in lock position and test for resistence on all pins, there should be none.
5. Disengage the engine and manage the hood. Grant engine to algid. Remove the annulling battery cable by loosening the cable clamp with a wrench. Stir the cable to the side. Abode the explanation in "ACC" position.
6. Remove the steering shove: turn the shove until completely straight, handle a customary screwdriver pry on the steering rotate mounting screw covers and remove.
7. Unscrew the steering circle mounting screws using a drawn out torx sense screwdriver and locate them outside from the office environment.
8. Pull elsewhere the center airbag module and unplug connector. Unplug the horn and cruise control connectors by pressing on release tab and pulling.
9. Remove the steering wheel mounting nut by using a ratchet and the correct size socket. Mark the steering wheel alignment with the steering shaft.
10.18. Reinstall the steering wheel mounting screw by using a long torx head screwdriver. Reinstall steering wheel mounting covers by pressing back into spot.
12. Unplug the ignition switch connector from the wiring harness by pressing the release tab and pulling.
Unscrew the ignition switch mounting screws using a Phillips screwdriver.
13. Remove the ignition switch from the vehicle and set off to side. With a small pick or screwdriver press the retaining pin for the lock cylinder and push upward. Pull the lock cylinder out of the housing while still pushing up on the retaining pin.
Installation
14. Push the new ignition lock cylinder retaining pin and insert new lock cylinder into housing until the retaining pin pops out and seats into the hole. Mount the new ignition switch and then install the mounting screws with a Phillips screwdriver.
15. Plug in the ignition switch connector to the wiring harness by simply pressing into the harness housing.
Install the steering wheel switches and mounting screws with a Phillips screwdriver.
16. Reinstall the steering wheel cover with a Phillips screwdriver. Install the steering wheel back onto splined shaft and align mark. Install the steering wheel mounting nut and torque down to Twenty six foot-pounds using a 3/8-inch torque ratchet and correct size socket.
17.Plug in the horn and cruise control connectors by simply pressing into connector housing. Reinsert the air bag module and connect the connector.
Pull the steering wheel off the splined shaft using a steering wheel puller tool and set steering wheel out of way.11. Remove the steering wheel cover by unscrewing the screws with a Phillips screwdriver. Then remove the steering wheel switches in the same manner.
19. Reinstall the negative and positive battery cables using correct-sized wrench.
Insert the key and try to pull out ignition cylinder. Start the unit and run for one to three minutes.
