Research the rotors for scoring and other damage while the brake pads are removed from the Motor lorry.
The braking step on legion makes and models of trucks varies slightly; nevertheless, the basic morals of replacing the brake pads remains consistent. Trucks with brake pads equipped with wear indicators excrete an audible alert when the brake pads corner reached a critical commensurate of wear. Change the brake pads at the earliest viable mo after the wear indicators are heard to save the brake rotors from damage. Benefit the befalling to examine the other components of your Motor lorry's braking meeting.
Instructions
1. Grounds the Motor lorry on a Apartment lodgings stretch of means or driveway. Pull the hood Proceeds lever. Proceeding to the front of the Motor lorry.
2. Clear the hood and remove the crack cylinder cap. The adept cylinder contains brake fluid. Remove one-third of the fluid in the reservoir with a syringe or baster. Lay the cap loosely over the container to grasp debris absent of the reservoir while relieving the energy in the reservoir. This helps to dehiscent the caliper pistons in subsequent steps.
Lower the rear end of the truck and tighten the lug nuts. Return to the driver's seat.23.
Consult your particular Motor lorry's repair notebook for recommended lift points.
5. Lift the front of the Motor lorry and habitat at least two jack stands subservient the frame for buttress.
6. Remove the lug nuts on the front wheels. Remove the wheels.
7. Remove the spring clips on the elsewhere of the caliper with a duo of pliers or Apartment lodgings screwdriver, provided spring clips are going on.
8. Unscrew the two caliper slide pins on the back side of Everyone brake caliper.
9. Lift the calipers (one for Everyone front brake meeting) gone from the caliper bridge and rotor. Rest the caliper on top of the rotor or steering arm. Discharge not let the caliper hang from the Motor lorry by the brake borderline.
10. Remove the brake pads from the caliper bridge. Pry the pads from the bridge or slide them from the bridge's slots, depending on the particular Motor lorry.
11. Gaze the caliper bridge and rotor. Change any components that are damaged or significantly worn. Place the jack under the frame at the back of the truck. Lift the truck's rear end, and support the vehicle with jack stands.20. Remove the rear wheels and replace the rear brake pads as described in steps Seven through 15.
13. Apartment a C-clamp or channel-lock pliers over the caliper piston and the back of the caliper. Squeeze the pistons into the side of the caliper to create margin for the different brake pads (and rotor, provided fundamental). Remove the clamp or pliers once the piston is completely recessed within the caliper.
14. Operate brake grease to the back side of the virgin brake pads. Contain them into the slots of the caliper bridge.
15. Place the caliper back over the new brake pads and caliper bridge. Apply anti-seize brake grease to the caliper pins and replace them into the caliper.
16. Place the wheels back on the truck's front wheel bolts, and screw on the lug nuts by hand.
17.Lift the front of the truck and remove the jack stands. Lower the front of the truck to the ground. Tighten the lug nuts with a tire iron or lug wrench.
18. Loosen the rear wheel lug nuts.
19. Consult your Motor lorry's repair textbook for directions on removing the brake rotors, provided required.12. Spray the caliper bridge and steering knuckle carry on the rotor with brake parts cleaner. Disinfected the nature with a wire brush to remove rust.
21. Place the rear wheels back on the truck's wheel bolts and screw on the lug nuts.
22. Lift the back of the truck with the jack and remove the jack stands.3. Loosen the lug nuts on the front wheels with the tire iron or lug wrench.4. Accommodation the lifting jack below the frame in the front of the vehicle.
Start the truck's engine and press the brake pedal repeatedly to reset the caliper pistons. Cease brake pedal depressions once the pedal response returns to normal. Move to the engine compartment.
24. Remove the master cylinder cap and place a funnel into the container. Add brake fluid to the reservoir until it is full.
25. Remove the funnel. Replace the master cylinder cap and close the truck's hood.
