As its own mould, the Silverado debuted in the One thousand nine hundred ninety nine design year, nevertheless the label dates back to its introduction as the top trim calm on Chevy pickups in 1975. The Two thousand two Silverado's mannequin trim flush came customary with a 200-horsepower, 4.3-liter Vortec V-6 engine and a five-speed transmission. Further average on the pattern commensurate Two thousand two Silverado are book windows. Ethical alike gift windows, these archaic devices appropriateness a regulator to lift and lower the window, on the other hand your arm acts as the Engine. Replacing the regulator on the mould constant Two thousand two Silverado requires partially disassembling the door panel, so account caution not to crack any of the plastic components in the development.
Instructions
Removal
Slide the courtesy lustrous meeting, whether equipped, toward the front of the door to Proceeds its rear locking tab. Pry outward on the rearmost contour of the courtesy luminosity meeting with a flathead screwdriver, then pull the meeting from the door panel. Twist the courtesy headlamp socket counterclockwise and pull it from the meeting. Locate the meeting aside.
2. Turn the window Eccentric person so its use points toward the front of the Motor lorry. Incorporate a window crank Emigration belongings between the door panel and window Eccentric person, so the belongings's utilize is perpendicular to the window Eccentric person's stem.
3. Press the window Eccentric person Emigration item downward until you mood it contact the window Eccentric person's U-shaped clip - you cannot gaze the clip, so you must engage in this by sense solitary. Authority one artisan under the window Eccentric person and press the factor downward to disengage the clip. Hire the clip with your other artisan as it falls outside.
4. Pull the window Eccentric person from the window regulator input shaft. Clutch the window Eccentric person in the identical position it was prior to removing it - the application facing the front of the Motor lorry - and involve the C-shaped clip into its slot on the rear of the Eccentric person, with the ajar cusp of the clip facing upward.
Remove the bolts with a ratchet and socket.13. Remove the four bolts securing the window regulator to the door, using a ratchet and socket. Fold the two sides of the regulator together and pull the regulator from the door, via the large access hole. Remove the trim from the door.
6. Pry the door lock lever meeting from the door panel, using a flat-head screwdriver. Pull the lock lever meeting off the door panel, which besides disengages the lock actuator rod from the lock lever.
7. Remove the two door panel-retaining screws - one in the lower front-most corner of the door panel and another inside the lock lever cavity - using a ratchet and socket.
8.1. Clear the door with the failed window regulator and assent it ajar. Remove the inside door handgrip bezel -- the trim abundance surrounding the inside door utilize -- by prying sorrounding its string with a flat-head screwdriver, then pulling it from the inside door helve.
9. Lift the door panel upward to disengage its retaining tabs and pull the door panel from the door, as you coerce the courtesy blaze wiring over the courtesy glossy cutout.
10. Involve a flat-head screwdriver's blade under the door's flood shield and into an earth of the shield's adhesive. Pull upward to tear the adhesive's seal, then remove the screwdriver. Using the broken world of the adhesive as your starting location, carefully peel the imbue shield from the door. Sit the irrigate shield in a Disinfected universe with its adhesive side up.
11. Pull the window up to its abundant up position and hold an assistant grasp it owing to position. Secure the window up with distinct 12-inch-long strips of duct tape.
12. Peep inside the door, via one of the access holes, and jewel the two bolts securing the window regulator to the window glass guides, the Trimmings glued to the bottom of the window.5. Include a flat-head screwdriver's blade under the front-most item of the upper margin trim, the triangle-shaped trim plenty above the front of the door panel. Pry outward on the front of the upper interval trim to Proceeds its retaining clips.
Installation
14. Guide the new regulator into the door and maneuver it until all of the bolt holes align and the regulator's input shaft sticks out from its hole in the door. Tighten the regulator-retaining bolts to Eighty inch-pounds, using an inch-pound torque wrench and socket.
15. Instruct your assistant to hold the window glass firmly as you remove the duct tape. Have your assistant lower the window until the bolt holes in the window glass guides align with their mounting holes in the regulator. Hand-tighten the regulator-to-window glass bolts, then tighten them to Eighty inch-pounds.
16. Set the water shield in place on the door, guiding the courtesy lamp wiring, if equipped, and regulator input shaft through their respective holes in the shield. Press the water shield onto the door firmly with your fingers to stick its adhesive to the door. In any areas that the adhesive has become weak, add a strip of waterproof double-sided tape to replace the adhesive.
17.Guide the courtesy light wiring, socket and bulb through its cutout in the door panel, if equipped. Align the retaining tabs on the rear of the door panel with their slots in the door panel. Slide the door panel downward to guide the tabs into the slots in the door.
18. Insert the courtesy light bulb and socket into the courtesy lamp assembly, if equipped, and twist the socket clockwise to lock it into place. Insert the courtesy lamp assembly into its cutout in the door panel and slide it rearward to engage its retaining tab.
19. Align the window crank with the regulator input shaft and press the crank onto the shaft until you hear the U-shaped retaining clip snap into place.
20. Tighten the trim panel's retaining screws to Eighteen inch-pounds, using an inch-pound torque wrench and socket.
21. Hold the door lock lever assembly up to its cutout in the door panel. Raise or lower the door lock lever, so the door lock actuator rod aligns with its retaining clip on the lever. Press the door lock lever assembly onto the door panel until it snaps into place.
22. Line up the retaining clips on the rear of the upper extension trim with the slots on the door. Press the trim onto the door until its clips snap into place.
23. Guide the inside door handle bezel over the inside door handle and line up the retaining tabs on the bezel with their slots in the door panel. Press the bezel onto the panel until the tabs snap into place.
