Remove the strut and coil assembly from the vehicle.
Install the New Strut
9. Remove the coil from the old strut, if you are replacing the strut only, using a coil spring compressor, ratchet and socket.Beyond that, you can lawns your Jetta in a garage, holding outside the toolbox and moderate the machine struts in a uncommon hours. Not lone Testament you restore your Volkswagen's handling and comfortable coerce, on the other hand save on repair costs further.
Instructions
Remove the Strut
1. Loosen the lug nuts on the front rotate/tire meeting you hope for to overhaul ahead with a lug wrench, and stand the circle using a floor jack. Help the vehicle with a jack stand under the frame, and Stop removing the spin meeting.
2. Unplug the ABS sensor, whether your specific imitation is equipped with it. The sensor is last the steering knuckle/hub meeting, where the revolve/tire meeting mounts on.
3. Unbolt the bracket holding the brake contour to the strut, above the steering knuckle, using a wrench.
4. Disinfected the two bolts and surrounding earth of the two bolts holding the top of the steering knuckle meeting to the backside of the strut meeting with a wire brush. Communication if the top mounting bolt has an eccentric washer -- a washer with an off-center gap. Whether it does, advantage a scratch Brad-awl to purpose the objective of the washer Towards its mounting mould so you alternate the washer in the duplicate position. This Testament nourishment preserve most of the shove alignment until you yield your Jetta for avail.
5. Unfasten the two bolts holding the brake caliper to its mounting bracket using a ratchet and socket. Remove the caliper, and tie it to a suspension Element with substantial wire to prevent damage to the brake hose connected to it.
6. Loosen the two bolts securing the steering knuckle meeting to the backside of the strut meeting with a ratchet and socket. Employ a backup wrench to clout the nuts as you remove the loosened bolts. Secure the steering knuckle with heavy wire to a stable component so it does not hang loose once you remove it from the strut assembly. When ready, finish removing the bolts, and pull the steering knuckle off the strut using a large screwdriver as a pry tool, if necessary.
7. Open the hood, and remove the cap from the top of the strut tower inside the engine compartment. Position an open socket over the retaining nut on top of the strut. Use an Allen wrench to hold the strut rod in the middle of the retaining nut. Loosen the strut-retaining nut with a ratchet as you hold the strut rod with the Allen wrench.
8. Ask an assistant to hold the strut assembly in place as you remove the strut retaining nut and mounting plate cap from the top of the strut assembly.
Utilize a torque wrench to tighten your struts to specification.Provided the struts in your One thousand nine hundred ninety three Volkswagen Jetta are leaking, damaged or ethical worn away, you might not be read if you are up to the profession. Your Jetta example has prepared these components rather accessible. Yet, you Testament require firm tools and concern to circumstance for the project.Install the coil spring on the new strut.
10. Ask an assistant to position the new strut assembly in place, and install the mounting plate cap and a new strut retaining nut hand-tight. Tighten the retaining nut to Forty four foot-pounds (60 Nm) using the open socket, Allen wrench and a torque wrench.
11. Replace the cap to the top of the strut tower, and close the hood.
12. Untie the steering knuckle assembly, and fit it into the bottom of the new strut assembly. Install the two mounting bolts finger-tight, and make sure the eccentric washer, if equipped, is properly aligned. Tighten the bolts to Seventy foot-pounds (95 Nm) using a torque wrench. Hold the retaining nuts on the bolts with a backup wrench.
13. Reinstall the brake caliper, and tighten the bolts with the ratchet and socket.
14. Secure the brake line bracket to the strut with the wrench, and plug in the ABS sensor, if equipped.
15. Replace the wheel/tire assembly, lower your Jetta, and finish tightening the lug nuts on the wheel assembly with the lug wrench.
16. Replace the strut on the other front wheel assembly, if necessary, following Step One from the previous section through Step Seven of this section, then close the hood.
